The Homeowner’s Guide to Residential Concrete Driveway Cost
Last Updated: November 5, 2026
Quick Summary
Residential concrete driveway cost in Brisbane depends on the area poured, the finish chosen, ground conditions and site preparation. Published national guide rates put plain concrete at $65 to $85 per square metre and coloured concrete at $75 to $95 per square metre, but these exclude site work, reinforcement, formwork and finishing. Two quotes for the same driveway can differ by thousands of dollars, and the gap is almost never about the concrete itself.
- Exposed aggregate is typically priced at $210 to $245 per square metre, with off-white exposed aggregate at $265 or more.
- A single-car driveway is usually around 3 metres wide, while a double runs closer to 5.5 to 6 metres.
- Reactive clay soils across the region swell and shrink with moisture, so a slab over inadequately prepared clay will crack.
- Excavation for a domestic driveway is typically 100 to 150 mm deep, but deeper where fill or organic material is found.
- Ask contractors for examples of work completed more than ten years ago to judge whole-of-life value.
Table of Contents
- What Drives Residential Concrete Driveway Cost in Brisbane
- Concrete Driveway Cost Per Square Metre: Plain, Coloured and Decorative Rates
- Exposed Aggregate Driveway Cost and Other Finish Options
- Typical Total Cost by Driveway Size
- Site Preparation, Excavation and Brisbane Site Conditions
- Concrete Driveway Quote Checklist: What a Fair Quote Includes
- Concrete Driveway Installation Time and Whole-of-Life Value
- Requesting an Itemised Quote for Your Driveway
- Frequently Asked Questions
What Drives Residential Concrete Driveway Cost in Brisbane
Residential concrete driveway cost in Brisbane comes down to four variables: the area being poured, the finish you choose, the condition of the ground beneath it, and how much preparation the site needs before any concrete arrives. Get those four right and the quote makes sense. Get them wrong and you will spend the next decade looking at cracks.
At Professional Concrete, we have poured residential driveways across Brisbane and the Gold Coast, and the pattern is consistent. Two quotes for the same driveway can differ by thousands of dollars, and the gap is almost never about the concrete itself.
Why quoted rates differ so much between contractors
A cheap rate usually means something was left out of the scope, not that the contractor is generous. The most common omissions are excavation depth, spoil removal, reinforcement grade, and the thickness of the slab.
Ask each contractor what depth of base they are allowing for and where the excavated material goes. Our guide to concrete contractor workmanship warranty in Brisbane explains what a fair warranty actually covers.
Concrete Driveway Cost Per Square Metre: Plain, Coloured and Decorative Rates
Concrete driveway cost per square metre is the number most homeowners fixate on, and it is also the most misleading.
According to hipages’ national concrete driveway cost guide, plain concrete is typically quoted at $65 to $85 per square metre and coloured concrete at $75 to $95 per square metre.
| Finish | Typical rate per m² (AUD) | Best for |
|---|---|---|
| Plain concrete | $65-$85 | Tight budgets, side access |
| Coloured concrete | $75-$95 | Matching house render or brickwork |
| Exposed aggregate | $210-$245 | Traction, coastal conditions |
| Off-white exposed aggregate | $265+ | Premium street appeal |
| Stencilled or stamped | Quote-specific | Pattern and texture effects |
Rates verified against Conker’s published driveway finish pricing should be read the same way: as a starting range, not a fixed price.
Exposed Aggregate Driveway Cost and Other Finish Options
Exposed aggregate is a labour-intensive finish. The surface is retarded and washed back to reveal the stone, which takes timing, water control and experience.
Stencilled and stamped concrete sit in a similar bracket, and both are worth the money only when the pattern suits the house. A stamped finish that fights the architecture looks dated faster than plain concrete ever will.
Typical Total Cost by Driveway Size
Total project cost scales with area, but not linearly. A small driveway carries a higher per-square-metre rate because mobilisation, minimum concrete loads and setup costs are spread across fewer square metres.
Single-car, double and long battle-axe driveways
A single-car driveway is typically around 3 metres wide (How Much Does A Concrete Driveway Cost? (2026)). A double driveway runs closer to 5.5 to 6 metres. Battle-axe driveways add length, and length adds cost through reinforcement, joints and often a pump truck for access.
| Driveway type | Approx. area | What pushes the total up |
|---|---|---|
| Single-car, standard length | 18-24 m² | Minimum load charges |
| Double, standard length | 33-40 m² | Reinforcement volume |
| Double with turning bay | 45-60 m² | Joint layout, drainage falls |
| Long battle-axe access | 60-100 m² | Pump access, joint frequency |
Use these areas to sanity-check any quote you receive. If the stated area does not match the measured dimensions, ask why before you sign.
Site Preparation, Excavation and Brisbane Site Conditions
Site preparation is where a residential concrete driveway quote in Brisbane diverges most from national guide rates. The concrete itself is a commodity; the ground beneath it is not.

What site preparation actually involves
A properly scoped preparation stage usually includes:
- Set-out and survey, marking levels, falls and the crossover point so water drains away from the slab and garage.
- Excavation, removing topsoil and any unsuitable material to a specified depth, typically 100-150 mm for a domestic driveway but deeper where fill or organic material is found.
- Base course, supplying and compacting a graded crushed rock base, commonly 100 mm compacted in layers, to give the slab uniform support.
Each of these is a separate cost line. A quote that lists “site prep” as one lump sum hides which of them are included and which are not.
How Brisbane site conditions change the price
The following local factors can affect preparation costs:
- Slope, a steep driveway needs deeper cut and fill, retaining at the edges, and sometimes a stepped or terraced design. Excavation and formwork labour rise accordingly.
- Soil, reactive clay may require over-excavation and replacement with a stable base, or a thicker slab with heavier reinforcement. Rock encountered during excavation can add significant time and equipment cost.
- Access, narrow side access, tight corners or a long battle-axe block may rule out a standard concrete truck reaching the pour. A line pump or boom pump is then needed, adding a mobilisation charge and hourly rate.
A quote that lists “site prep” as one lump sum, without a stated excavation depth, base specification and spoil arrangement, can later become a variation once work starts.
What to ask before signing
Ask each contractor to state, in writing: the excavation depth and what happens if unsuitable material is found; the base material type and compacted depth; whether spoil removal and tip fees are included; the concrete strength grade and slab thickness; the reinforcement type, grade and spacing; and how falls and stormwater discharge will be handled. Those answers, not the headline rate, are what make quotes comparable.
Concrete Driveway Quote Checklist: What a Fair Quote Includes
A fair quote is itemised, dated and specific. Use this checklist to compare submissions line by line rather than on the total alone, and use the questions below to test whether the contractor can explain what each line means.
What every quote should state
- Measured area with dimensions, not an estimate
- Excavation depth and base course specification
- Spoil removal included or excluded, with tip fees noted
Questions that separate a thorough contractor from a cheap one
- “What depth of base are you allowing, and what happens if you hit rock or fill?” A contractor who has priced the site will answer specifically. A vague answer usually means the risk is being pushed to you as a variation.
- “Where does the spoil go, and is the tip fee in this price?” Spoil removal is a real cost. A quote that assumes you will deal with it is not cheaper, just incomplete.
- “What concrete strength and slab thickness are you specifying, and why?” Domestic driveways carrying cars typically need a higher grade and thickness than a garden path. If the answer is the same for every job, the quote is not engineered to your site.
- “How are control joints laid out, and at what spacing?” Joint layout controls where cracks appear. A contractor who cannot describe it is unlikely to get it right.
- “Can you show me work you completed more than ten years ago?” A driveway still holding up after a decade of local summers tells you more than any brochure.
- “What is excluded from this price?” The exclusions list is often more revealing than the inclusions.
Warning signs in a quote
A quote that is dramatically lower than the others may have a scope item missing, such as excavation depth, spoil removal, reinforcement grade or slab thickness. Ask what was left out before you treat it as a saving.
Other red flags include: no licence or insurance details; a warranty offered verbally only; a finish described only as “decorative”; no stated start date; pressure to pay a large deposit in cash; and a quote that will not put the area dimensions in writing.
How to compare quotes fairly
Put the quotes side by side and align the line items. Where one quote is silent on a line, treat it as excluded until the contractor confirms otherwise in writing. The lowest total is only the lowest total if every quote covers the same scope, and on residential driveways, they rarely do.
If you are still at the stage of gathering submissions, our guide to getting a quote for residential concrete work walks through how to request and compare them properly.
Concrete Driveway Installation Time and Whole-of-Life Value
Installation time for a residential driveway depends on the job, and weather can affect the schedule, so confirm timing with the contractor before work begins.
The whole-of-life calculation is where cheap quotes lose. Our article on how to avoid concrete cracking covers the control joint and reinforcement decisions that determine how a slab ages.
Ask any contractor for examples of work completed more than ten years ago, as a driveway still holding up after a decade of local conditions says more than any brochure.
Requesting an Itemised Quote for Your Driveway
An itemised quote gives you the ability to compare fairly, question specifics and understand what you are paying for. Ask for it in writing, with the scope broken down by stage rather than presented as a single figure.
If you have questions about timelines, materials or how the process runs, our frequently asked questions page covers the common ones before you get in touch. When you are ready, you can contact our team to request an itemised quote for your driveway.
Frequently Asked Questions
How much does a residential concrete driveway cost per square metre?
Installed rates depend on what is included, so the best way to compare is to request a quote. The gap reflects what is included: excavation, reinforcement, formwork and finish are often priced separately. Ask for an itemised rate so the concrete driveway cost per square metre you compare covers the same scope.
How much does an exposed aggregate driveway cost compared with plain concrete?
Exposed aggregate sits above plain concrete. The exposed aggregate driveway cost reflects the extra labour in washing back the surface and the premium aggregates used. It suits sloped or high-visibility driveways where slip resistance and appearance matter.
What should a concrete driveway quote include?
A fair quote lists excavation and spoil removal, formwork, reinforcement mesh or bar, slab thickness, concrete supply and pumping, finish type, control joints, drainage falls, and cleanup. It should also state whether council crossover approval and any footpath or nature strip reinstatement are included. Use a concrete driveway quote checklist to compare quotes line by line rather than on the bottom figure alone, because inclusions vary widely between contractors.
How long does it take to install a concrete driveway?
Installation time depends on the job, and weather, site access and council approvals can all affect the schedule, so confirm timing in writing before work starts.
Does driveway pricing include excavation and site preparation?
Not always. Some advertised per-square-metre rates cover only supply, placing and finishing, with excavation, removal of old concrete and base preparation charged separately. Site preparation on reactive clay soils or sloping blocks can add significant cost. Ask each contractor to confirm in writing whether excavation, spoil removal and base compaction are included, so the comparison reflects the full project cost rather than a partial rate.
What factors affect the cost of a concrete driveway?
The main factors are driveway area and dimensions, finish selection, slab thickness and reinforcement, site access for trucks and pumps, slope, soil conditions, drainage requirements, and whether an old surface needs demolition and removal. Council crossover requirements and any footpath works also affect the total. Two driveways of the same size can differ by thousands of dollars once these site and engineering choices are priced.
Getting a driveway quote that actually reflects your site is the difference between a surface that lasts and one you regret. Professional Concrete brings over 17 years of combined industry experience to every residential job, from meticulous site preparation through to detailed finishing, with workmanship tailored to your specifications and reliable project management from start to completion. Get started with Professional Concrete and request an itemised quote for your driveway.

